Silhouette fully engaged
on "Z" Clip
Ceiling bracket
Mounting fasteners
(supplied by others, 2 per bracket)
(front of Silhouette case)
(right end of Silhouette case)
Copyright © 2003 Draper Inc. Form SilhouetteE&V220V_Inst03 Printed in U.S.A.
Installation/Operating Instructions
220V Silhouette/Series E & V Electric Projection Screen by Draper
Installation
Your Draper screen can be mounted on a wall or suspended from the ceiling,
or mounted on special 15 cm or 30 cm extension brackets. Extension brackets
must be ordered separately from Draper. With each method of in stal la tion, the
case must be mounted level and with the fl at back parallel to the wall.
To reduce the risk of personal injury, use only the hardware which comes with
the screen or is specifi ed in these instructions.
The screen (or extension brackets) should be mounted into studs or blocking
in the wall/ceiling, or in drywall (minimum thickness 13 mm [
1
/
2
"]) with speci-
fi ed anchors. For any other type of installation, follow all local build ing and
safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood
frame construction require the use of special screws or anchors. The selection
of ap pro pri ate mounting hardware should be made by a qualifi ed pro fes sion al
installer.
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in case.
Take care to install wall/ceiling electrical box and conduit so they will be fully
concealed by the screen case after installation.
Handle case carefully to avoid scratching.
Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface will
not cause case to work loose or fall. Installer must insure that fasteners used
are of adequate strength and suitable for the mounting surface chosen.
Ceiling/Suspended Mounting
Lo cate two off set ceil ing brack ets (supplied) and slide these into the channel
on top of screen case by angling one side of bracket under lip of channel and
opposite side of bracket above notch in opposite channel lip.
Allow bracket to drop against bottom of channel and then slide it along case
until it stops against end cap of case. Tighten two set screws to lock bracket
in place. Make sure that the fl ange of the ceiling bracket that has four holes
is extended beyond the end caps of the case. Repeat above procedure for
second ceiling brack et, making sure to slide it towards op po site end of case.
Wall Mounting
Mount two, three or four aluminum brackets provided (“Z” Clips) on the wall
at desired height, using appropriate fasteners. Verify that they are in line and
level to fully engage with the mounting lip on back of screen case. 42 mm of
free space is required above the “Z” Clips to allow case lip to be engaged over
the lip of the “Z” Clips.
Engage the lip on back of screen case with lip of “Z” Clip and gently pull down
to fully engage case to brackets.
These instructions are meant as a guide only. They do not
imply any re spon si bil i ty on the part of Draper, Inc. for improper
in stal la tion or faulty work man ship at the jobsite.
Caution
➀ Read instructions through completely before proceeding; keep them for
future reference. Follow instructions carefully. Installation con trary to
instructions in val i dates warranty. Care in mounting and correct oper-
ation will mean long and satisfactory service from your Draper screen.
➁ Screen should be accessible for complete removal should fabric
become damaged or should other service be required.
➂ Screen should be installed level (using a carpenter’s level).
➃ Nothing should be fastened to screen dowel or viewing surface
➄ Operating switch(es) packed separately in screen carton. Do not
discard with packing material.
➅ Screen operates on 220V, 50 hz., 1 ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Lip on back of case
"Z" Clip
(wall mounting bracket
supplied with Silhouette)
Ceiling bracket in
channel of case
To mount against ceiling, hold screen case against ceiling and mark mount-
ing hole locations. Each brack et has two holes towards the front edge and
two holes towards the back edge. Installer must use at least two fasteners
per bracket with one fastener in one of the two holes clos est to back edge
of bracket, and one fas ten er in one of the two hole closest to front edge of
bracket. Installer must insure that fasteners are of adequate strength and suit-
able for the mounting surface chosen.
If you encounter any diffi culties installing or ser vic ing your Artisan
Series screen, call your dealer or Draper, Inc. Spiceland, Indiana,
U.S.A., telephone (765) 987-7999, fax (765) 987-1689, or email
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals