Draper SL10 User Manual download pdf (Page 2)

➃ Select Optional Accessories

Optional Ceiling Access Door (2 x 2) to allow access above ﬁ nished ceiling (highly recommended)

White Painted Finish Accepts Ceiling Tile

Optional SMS Low Proﬁ le Mount and Universal Bracket

A) If you selected the SMS Low Proﬁ le Mount please provide the following Projector information (supplied by others)

Manufacturer

Make/Model Projector Size H x W x L:

Optional plenum housing: optional ceiling closure panel not included.

B) If you selected the plenum housing option please provide the following information:

Projector Size H x W x L:

Bracket height: Available space above ceiling:

Optional ceiling closure panel.

Optional ceiling ﬁ nish kit: consists of ceiling closure panel and mating trim kit to ﬁ nish ceiling opening.

C) If you selected one of the above options please use the following chart to select the correct size plenum housing, ceiling closure, or ceiling ﬁ nish kit:

Size B Size S Size E Size J Size G Size U

(SL Only) (SL Only)

Max. Projector Size W x L 25" x 25" 25½" x 27½" 25½" x 35½" 25½" x 39½" 31½" x 44½" 27½" x 30½"

Ceiling Opening W x L 29

" x 29

" 29½" x 32" 29½" x 40" 29½" x 44" 35

" x 49" 36

" x 36

" (Trim edge–to–edge)

Ceiling Closure Panel W x L 30

" x 30

" 30" x 32½" 30" x 40

" 30" x 44½" 36

" x 49½" 37

" x 37

" (Trim edge–to–edge)

➄ Do you want the optional factory installed hookup for RGB, Video and Projector Control? Yes No

A What type of connectors do you need on Inputs (to Projector)? What type of connectors do you need on Outputs (to Lift)?

BNC How Many? BNC How Many?

15 Pin HD How Many? 15 Pin HD How Many?

RCA How Many? RCA How Many?

S-Video How Many? S-Video How Many?

RS232 (DB9) How Many? RS232 (DB9) How Many?

➅ Select Voltage:

110-120V

220-230V

➆ Select Controls: This unit comes with one 12v Toggle Switch and 12v Momentary Key Control. For other switching

options, please select from below:

Optional Video Interface Control (VIC12) for projection screen operation

Optional Key Operated Power Supply Key Switch (On-off)

Optional Low Voltage Control (LVC-III)—24V*

Specify number of switches (LVC-S)

(Controls the "Show" position only)

*This is required for any of the following options:

Wireless Remote Control (radio frequency transmitter & receiver) (Controls the "Show" position only)

Wireless Remote Control (infrared transmitter & receiver) (Controls the "Show" position only)

➇ Will this unit be controlled by other equipment?

No.

Yes. What kind of equipment?

Scissor Lift Submittal & Planning Sheet for SL and SLX Series page 2 of 4

DRAPER SALESPERSON:

CUSTOMER CONTACT:

SIGNATURE:

www.draperinc.com

(765) 987-799

Speciﬁ cations—Scissor Lift

video projector lifts, Model (SL4/SL5/SL6/SL7/SL8/SL9/SL10/SLX11/

SLX12/SLX13/SLX14/SLX15/SLX16/SLX17), for projectors weighing up to 350#.

Dove grey baked powder coat ﬁ nish. Projector bolts onto operating pan, or mounts

to pan with optional SMS Low Proﬁ le Lift Bracket (projectors through 26 lbs only).

Electrically op er at ed 110-120V AC, 60 Hz. UL rec og nized gearmotor, with metal

chain drive system, to be lifetime lubricated.

For SL Models: Projector to be sus pend ed from 2¾" x 20" x 20" x 11 ga. steel

pan supported by steel scissor arms and operated by two

" aircraft cables with

2000 foot/pounds tensile strength per cable.

For SLX Models: Projector to be sus pend ed from 3

" x 24" x 26" x 11 ga. steel

pan supported by steel scissor arms and operated by two,

" aircraft cables with

4200 foot/pounds tensile strength per cable.

Equipped with 3 sets of stabilizing scissors, positioned on the left, right, and

rear sides. Also equipped with fail-safe inertial safety belt system and Cable

Management System with projector power cord. Factory set limit switches to

automatically stop travel at store, show, and service positions. Single Station

Control, standard, consists of one 12V toggle switch to lower lift from “stored” to

“show ” positions, and one 12V momentary key switch to lower lift from “show” to

“service” position. Optional LVC-III for operation from “stored” to “show” positions

only; required for use with Key Operated Switch.

Optional plenum housing consists of suitable painted steel panels for use in return

air plenum situations. Optional ceiling closure panel, ﬁ nished in white baked

textured powdercoat, shall descend smoothly with projector. Choose a model

based on number of feet needed (4'-9'/11'-17') to put projector within easy reach

for servicing.

Please Note: The Scissor Lift should be speciﬁ ed in conjunction with a DRAPER

motorized screen.

SMS Low Proﬁ le Fixed Mount: Ceiling mount shall consist of a steel ball joint and

Universal Projector Bracket. Mount shall be 2" long, and shall securely attach to

lift with steel mounting plate (provided). Installer shall provide mounting hardware

appropriate to ceiling conditions. Steel ball joint attaches to Universal Projector

Bracket with twist-lock engagement. Min. overall height of assembled unit shall

be 4

". Mount shall provide up to 30° roll or pitch adjustment and 360° yaw

adjustment at ball joint. Two setscrews lock ball joint in position. Max. load 26 lbs.

Optional Ceiling Access Door: Provides access to projector and lift when unit is

installed above hard ceiling. Choose one: [White painted ﬁ nish/accepts ceiling tile].

Downloadable 3-part speciﬁ cations are available at www.draperinc.com.

1 2 3 4

Comments to this Manuals

No comments

Draper SL10 User Manual Page 2

Comments to this Manuals

Related products and manuals for Projector mounts Draper SL10