Draper LVC-III User Manual download pdf

Installation/Operating Instructions

Baronet/HW 110V and 220V Electric Projection Screen by Draper

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish appropriate hardware as required.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may

be mounted as in suspended or wall installation. Angles may be used (pro-

vided by others).

Electrical Connections

Screen operates on 110-120V AC, 60 Hz./220V AC, 50 Hz. or 60 Hz. current,

depending on model ordered. Duty Cycle: On 26 seconds/off 3 minutes.

Junction box is located inside left endcap and cover plate is secured to

endcap with two screws. Junction box contains pigtail leads and grounding

screws, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with National and

local electrical codes.

All operating switches should be “off” before power is connected. Do NOT wire

motors in parallel.

Hanging Screen

General:

When locating viewing surface and checking clearance for screen’s opera-

tion, remember surface is centered in case. Handle case carefully to protect

its ﬁnish.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for mounting surface chosen.

Suspended Installation:

Suspend screens from holes in top of endcaps as shown. "S" hooks, chains

(or cable) and turnbuckles should be provided by installer. “S” hooks should

go through the front holes on the endcaps (see drawing below), and both

ends of the “S” hooks should be crimped for additional safety. Chains should

be attached to beams or other structural members. Turnbuckles should be

adjusted so screen hangs level.

If you encounter any difﬁculties installing or servicing your Baronet/HW screen, call your

dealer or contact Draper, Inc., Spiceland, Indiana, +1 765-987-7999 or fax +1 765-987-1689.

Caution

 Read instructions through completely before proceeding.

 Follow instructions carefully. Installation contrary to instructions invali-

dates warranty.

 Screen should be accessible for complete removal should fabric be-

come damaged or should other service be required.

 Screen should be installed level (using a carpenter’s level).

 Nothing should be fastened to screen dowel or viewing surface.

 Operating switch(es) packed separately in screen carton. Do not dis-

card with packing material.

 Screen operates on 110-120V AC, 60 Hz. or 220V AC, 50 Hz. or 60 Hz.

current, depending on model ordered.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Operation

Before operating screen, remove small foam pieces which keep dowel in case

during shipping.

Screen is equipped with a 3-position operating switch, located on the power cord.

To lower the screen, move switch down. Screen will stop automatically when lower

limit switch is reached. To raise the screen, move switch up. Again, the screen

will stop automatically when the upper limit switch is reached. The screen may

be stopped in any intermediate position by moving the switch to the center “off”

position during operation.110-120V/220V Single Station Control — 3-position

up-off-down switch permits operation to be stopped at any point. Factory adjusted

limit switches automatically stop screen when fully down or fully up. 220V version

is CE certiﬁed.

110-120V/220V Multiple Station Control—Switches are similar in appearance

to 110V/220V Single Station Control. Screen stops when switch is released and

may be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully up or fully down.

24V Control — Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop

screen when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are optionally

available with this unit.  The key-operated power supply switch controls power to

the screen and switches. When it is “off ”, the switches will not operate screen. Key

may be removed from the switch in either “on” or “off” position.  A three-position

key switch permits the screen to be operated directly by key. In this case, the

screen’s operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Adjustments

Please Note: Screen limits are factory set for optimum performance of the

screen. Any adjustment of these limits could void the warranty. Please

check with Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before adjusting limit

switches.

“Down” limit switch: Down stopping position can be adjusted by turning white

knob with a screw driver or hex wrench. Turning knob counterclockwise will allow

viewing surface to run farther down. Turning it clockwise will reduce the amount of

exposed viewing surface.

“Up” limit switch: Up stopping position can be adjusted by turning red knob

with a screw driver or hex wrench through the small grommet. Turning knob

counterclockwise will allow surface to run farther into screen case. Turning it

clockwise will allow viewing surface to stop farther out of screen case.

Minimum 5 cm wide

slot for passage of

viewing surface if

suspended above ceiling

Example of

suspension

above ceiling.

Ceiling tile

and grid

(by others)

Back hole for wall mounting.

Hardware by others.

Top Hole for

suspended mounting.

Hardware by others.

Mounting angle

and hardware

by others.

Suggested for

recessed

installations.

Crimp

These Installation/Operating Instructions are available in the ofﬁcial language

of the country where you purchase the product. Please contact your

distributor to request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises

dans la langue ofﬁcielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

ofﬁziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

Baronet/HW 110-120V

AC version is certiﬁed by

Underwriters’ Laboratories, Inc.,

for the U.S. and Canada.

Baronet/HW220V AC

version is CE certiﬁed.

Front

Rear

1 2

Summary of Contents

Page 1 - Adjustments

Installation/Operating InstructionsBaronet/HW 110V and 220V Electric Projection Screen by Draper Wall Installation:Mount screen through holes in back

Page 2 - Case Dimensions

Baronet/HW by Draper Page 2 of 2 Fabric width + 5¾" (146 mm)3¼"(83 mm)3¾"96 mmViewing Surface3¼"(83 mm)Wiring DiagramsCase Dimensi

Comments to this Manuals

No comments

Draper LVC-III User Manual

Browse online or download User Manual for Projectors Draper LVC-III. Baronet/HW 110V and 220V Electric Projection Screen by Draper

Summary of Contents

Comments to this Manuals

Related products and manuals for Projectors Draper LVC-III