Draper VIC-12 Operations Instructions download pdf (Page 2)

Accessory Access ACXLE & ACXLV Roller Installation

Please note: When ordering a motor with built-in Low Voltage Controller, if the

case ships separate from the "guts," the case includes the 762cm cable and

special low voltage switch.

① Remove the bottom access panel (see "Bottom Access Panel Installation/

Removal" section above).

② The motor end mounting bracket has a metal bracket with snap ring for

accepting motor head. The idler end mounting bracket has spherical ball

bearings for accepting the idler pin. Both brackets have four set screws that

will be used to tighten the brackets in place inside the case. Back out the

four set screws in bracket until they are ﬂ ush with top side of bracket, then

remove the roller assembly from the shipping brackets, placing the roller

assembly on a ﬂ at, clean surface (see Fig. 5).

Please Note: Do not lose the snap ring and screw from the motorized

end, or the eight nylon washers, spring lock washer, fender washer and

machine screw from the idler end. They are required for re-attaching the

roller assembly to the brackets inside the case.

③ To engage the motor end bracket ﬂ ange above the two channels in the top

of the screen housing, rotate the bracket approximately 45° counter-

clockwise to allow the top surface of the motor bracket to rest ﬂ at against

the top inside of the housing. Rotating the bracket clockwise until it is

engaged with the mounting channel, slide it along the length of the housing

against the electrical junction box. Note: Set screw collar side of the bracket

must point toward the center of the case.

Caution: Do not allow the bracket to rotate and fall out of the channel.

④ Tighten all four set screws.

Motorized Roll er/Fab ric Re mov al

Reverse the in struc tions above “Motorized Roll er/Fabric Installation” for

re mov al of the unit.

Operation

When screen is ﬁ rst op er at ed, be cau tious! Cy cle unit down and up sev er al

times to con ﬁ rm sat is fac to ry operation.

220V SINGLE STATION CON TROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Fac to ry ad just ed limit switches

au to mat i cal ly stop screen when fully down or fully up.

220V MULTIPLE STATION CONTROL—(Not CE Approved) Switches are

similar in ap pear ance to 220V Single Station Control. Screen stops when

switch is re leased and may be re start ed in either direction. Factory adjusted

limit switches stop screen au to mat i cal ly when fully up or fully down.

24V CONTROL—Three-button UP-STOP-DOWN switches stop at any

point desired, operate in any se quence. Factory adjusted limit switches

automatically stop screen when fully up or fully down. Installer should

incorporate an all-pole disconnect in the ﬁ xed wiring.

220V & 12V VIDEO INTERFACE CONTROL—(Not CE Approved) Allows

Access XL case as seen from below

Bottom flange of Access housing

Bottom access panel pushup

points for panel removal

Caution: Beware of pinch

points at ends of closure

Figure 4

② Disengage closure from extrusion inside the case. Rotate closure as

shown in Fig. 4 and remove, holding it so the closure remains in this posi-

tion and does not bow before placing it on a ﬂ at surface.

Access XL 220 Volt Instructions by Draper page 2 of 5

www.draperinc.com

(765) 987-799

⑤ Replace the eight Nylon Washers into the idler end of the roller assembly.

⑥ Loosen the carriage bolts which attach the ﬂ ange-mounted bearing to the

idler end bracket just enough to allow the bushing some limited movement,

which will help when installing the roller assembly.

⑦ Rotate the bracket into the mounting channel located in the case top (when

mounting the roller assembly into the case). Both the bracket ﬂ ange and set

screw collar side of the bearing must point toward the gudgeon assembly.

⑧ Raise the roller/fabric assembly up into the screen housing and engage the

head of the motor completely into the motor mounting bracket, making sure

the snap ring engages with the motor and that the limit switch adjusting

knobs are visible from the bottom of the screen housing (see Fig. 6).

Caution: Due to the weight of the roller assembly, this step requires at

least two people to perform safely.

⑨ While supporting the idler end of the roller, slide the idler end mounting

bracket toward the roller. Slide the bearing over the end of the shaft.

Caution: Do not allow bracket to rotate and fall out of channel!

Align the bracket into the housing and tighten all four of the set screws.

Lock the roller assembly into place on the mounting bracket with the fender

washer, spring lock washer and machine screw (see Fig. 7).

⑩ Re-tighten the carriage bolts in the Idler-end Bracket Assembly so that the

ﬂ ange-mounted bearing is locked in place (see Fig. 5).

⑪ Tighten the two set screws in the bearing collar.

⑫ Con nect elec tri cal plug from mo tor to mat ing sock et on junc tion box.

⑬ Re in stall the bot tom access panel as pre vi ous ly de scribed (see Figs 3 & 4).

Caution: When placing the roller assembly into the case, be sure

motor is fully re-seated in the bracket, and secure it carefully with the

motor retaining spring and screw. Limit adjustment screws should be

facing down to allow access to them.

Please note: Maximum torque for

tightening screw is 6.77 Nm.

Figure 6

Figure 7

8 Nylon

Washers

Idler End

Roller Bracket

Fender

Washer

Spring

Lock

Washer

Machine

Screw

Roller

Setscrews

Gudgeon

Assembly

Carriage

Bolts

Bearing

Collar

Setscrews

Motor End (Series V shown) Idler End (Series E shown)

Figure 5

Carriage

Bolt

Shipping Brackets

1 2 3 4 5

Comments to this Manuals

No comments

Draper VIC-12 Operations Instructions Page 2

Comments to this Manuals

Related products and manuals for Projection screens Draper VIC-12